Maintenance Instructions LAMPS A tanning bed is only effective with working lamps. Tanning bed lamps are rated to a certain number of usage hours before the manufacturer recommends that you change them. These usage hours are different for each model of lamp and for each manufacture. Your lamps have a manufacture usage rating of 1200 hours. Through our experience, AJ's Tanning Sales & Service recommends that you change your lamps every 800 usage hours.
We have found that after the 800 hour mark lamp performance decreases very rapidly, and your customers will notice a difference in their tan. Below is a very simple graphical representation of your beds Performance to Usage Hours. Lamps will rarely actually burn out. If you have a lamp that appears to be burned out, try these steps: 1) Switch the lamp out with the neighboring bulb on either side, to test whether the problem is the bulb or the receptacle.
If the problem is the receptacle, repeat the same test with the starters. 2) The starter is a cylinder roughly the diameter of a penny. To remove the starter, grasp it firmly and turn it 1/2 turn counterclockwise. The starters are the most sensitive component of the bed, and are designed to protect the bed by burning out in case of an overload, rather than discharging into the bulb and damaging it. More often than not this will be the reason your lamp is out. NOTE:You should change your starters every second lamp change ACRYLICS To change your acrylics, remove the thumb screws on the hinge side of the bed.
(They are usually blue or white) Slide the acrylic in toward the hinge side of the bed, and remove it by gripping through the notches on either end of the bed and lifting or dropping it. (carefully) Please refer to the following picture for a visual step-by-step. It is recommended that you remove your acrylic, and clean both the backside of the acrylic as well as your reflectors every 2 months. CLEANING Only clean your bed with Ph Neutral, hypoallergenic disinfectant.
Cylinders & Springs - Gas Shocks - Pistons Order Toll Free 1-866-373-5700 Piston Replacement Guide Piston Description Cylinders & Springs Choose your tanning bed manufacturer from the list below and click for more information, or you may click on pages 1 thru 10 and browse through each page. Page:. Have the make, model, and year of your tanning unit ready.
Write down any and all numbers that are on your existing cylinders. Please write them down exactly. These numbers are very important to the ordering process, because they usually tell the type of cylinder end, the type of gas, the length, and the strength. Generally, the most important number is the number that ends with the letter 'N'. In some cases, the label may be worn beyond legibility, or completely missing. Sometimes you can take the cylinder off of the bed and hold it up to the light to see any engravings that may be on the part.
If you have no information at all off of the cylinder, you will then be require to measure the cylinder. With the cylinder completely extended (at its longest), take a measurement from end to end.
Then, take a separate measurement of the barrel (the thick part of the cylinder). These measurements paired with the bed information should help us locate correct replacement cylinders. If all else fails, it may be required that you send us your cylinder for in house determination of a replacement.
Older Montego Bay Celebrity Tanning Bed
Order Toll FREE 866-373-5700.
Cylinders & Springs - Gas Shocks - Pistons Order Toll Free 1-866-373-5700 Piston Replacement Guide Piston Description Cylinders & Springs Choose your tanning bed manufacturer from the list below and click for more information, or you may click on pages 1 thru 10 and browse through each page. Page:. Have the make, model, and year of your tanning unit ready.
Write down any and all numbers that are on your existing cylinders. Please write them down exactly. These numbers are very important to the ordering process, because they usually tell the type of cylinder end, the type of gas, the length, and the strength.
Generally, the most important number is the number that ends with the letter 'N'. In some cases, the label may be worn beyond legibility, or completely missing. Sometimes you can take the cylinder off of the bed and hold it up to the light to see any engravings that may be on the part. Fxfactory pro registration code keygen mac. If you have no information at all off of the cylinder, you will then be require to measure the cylinder. With the cylinder completely extended (at its longest), take a measurement from end to end. Then, take a separate measurement of the barrel (the thick part of the cylinder).
These measurements paired with the bed information should help us locate correct replacement cylinders. If all else fails, it may be required that you send us your cylinder for in house determination of a replacement. Order Toll FREE 866-373-5700.
Cylinders & Springs - Gas Shocks - Pistons Order Toll Free 1-866-373-5700 Piston Replacement Guide Piston Description Cylinders & Springs Choose your tanning bed manufacturer from the list below and click for more information, or you may click on pages 1 thru 10 and browse through each page. Page:. Have the make, model, and year of your tanning unit ready. Write down any and all numbers that are on your existing cylinders.
Please write them down exactly. These numbers are very important to the ordering process, because they usually tell the type of cylinder end, the type of gas, the length, and the strength. Generally, the most important number is the number that ends with the letter 'N'. In some cases, the label may be worn beyond legibility, or completely missing. Sometimes you can take the cylinder off of the bed and hold it up to the light to see any engravings that may be on the part.
If you have no information at all off of the cylinder, you will then be require to measure the cylinder. With the cylinder completely extended (at its longest), take a measurement from end to end. Then, take a separate measurement of the barrel (the thick part of the cylinder). These measurements paired with the bed information should help us locate correct replacement cylinders.
If all else fails, it may be required that you send us your cylinder for in house determination of a replacement. Order Toll FREE 866-373-5700.
Hello, If you are talking about a hard cover, what you need to do is open the tailgate and look at the underside of the cover. You should see some contact pads on top of threaded shafts. These contact pads need to be adjusted to allow for the locking mechanism to work. The lid must go down far enough for the lock cables(rods) to expand and secure the lid.
You may need some Torx or Allen-headed sockets to turn the parts. With the tailgate open, you can see what needs to be done. You might want to check any Bed mounts you can see as they may have loosened up. The side locks of the Bed require just the right amount of length in the Horizontal lock rods. If they are too long, you will never get the lid open with the handle once you close it.
I hope my Solution is very helpful to you. Jun 25, 2011.